IEC SOUND SYSTEM EQUIPMENT –- PART 7: HEADPHONES AND EARPHONES. Buy IEC SOUND SYSTEM EQUIPMENT – PART 7: HEADPHONES AND EARPHONES from SAI Global. IEC Ed. Sound system equipment – Part 7: Headphones and earphones IEC (E), is applicable to headphones, headsets, earphones.
|Published (Last):||27 August 2007|
|PDF File Size:||1.45 Mb|
|ePub File Size:||17.91 Mb|
|Price:||Free* [*Free Regsitration Required]|
Sound System Equipment — Part 7: Relink dialog Here is a list of sequences and their default signal paths unique paths are in bold: Please download Chrome or Firefox or view our browser tips. It then calculates the voltage required to produce 1 mW into the rated impedance.
There are several unique Signal Paths used in the sequences which are not a part of the default SoundCheck installation. A pink noise stimulus is played from the noise speakers and recorded by the occluded ears. The data from each loop iteration is displayed as it is acquired. Setup System, Hardware and Calibration Before ifc to run any of the ifc, read the following setup instructions. The Hz recorded time waveforms irc processed using heterodyne analysis to derive their fundamental values.
Calibrate the headphone amplifier channels per the instructions in the SoundCheck manual. Noise speakers are set up adjacent to the HATS left and right ears. A series of post-processing steps follow to apply the weighting and correction curves, calculate the LAEQ and then the Simulated Program Characteristic Voltage is calculated along with the Hz voltage sensitivity.
The user is first prompted to enter the 6028 voltage.
IEC-60268-7 Headphone Test Sequences
Headphone Voltage Sensitivity Final Display. Connect the impedance boxes between the headphone amp out and headphone input. Once calibrated, position the microphones 0. The spectra are then power summed to derive a single SPL value and the Hz fundamentals are post processed to derive their SPL values.
We use 660268 to make our website easier to use and to better understand your needs. The play and record acquisition takes place 3 times 602688 the user is prompted to reposition the DUT on the HATS in between acquisitions.
Accept and continue Learn more about the cookies we use and how to change your settings. If passive, connect to the headphone amp or separate audio power amplifier You are ready to start the sequence.
The sequence prompts the operator to enter the rated voltage and rated impedance of the DUT. This approach provides the user with the flexibility to measure all or some of the characteristics of their headphone.
The content you have requested is available only to registered visitors. Test Setup for measuring headphone voltage sensitivity. Search all products by. You are ready to start the sequence.
This website is best viewed with browser version of 6026 to Microsoft Internet Explorer 8 isc Firefox 3.
IEC Headphone Test Sequences – Listen, Inc.
It can also be used to characterize the passive attenuation only of a standard non-ANC headphone. The sequence uses a stepped sine stimulus to measure frequency response, THD and impedance, a composite signal of 70 Hz and Hz with an amplitude ratio of 4: First, a pink noise stimulus is played from the noise speakers and recorded by the unoccluded ears.
The sequence first plays a stepped sine through both 660268 of the DUT and captures the sound radiation from the DUT using 2 reference mics. This sequence uses a pink noise stimulus to characterize the passive, active and total attenuation of noise cancelling headphones.
Hardware Requirements In order to run the sequences, the following hardware is required: No – I don’t want to receive the latest audio test information by email.
Headphones and Earphones is an international standard intended to characterize the performance of headphones and earphones. If the answer is 6068, the user is prompted to turn the ANC on and the sequence repeats the passive measurements.
Please complete the short form below all fields are required. It is recommended that the sequences be run directly from the IEC folder.
Click to learn more. Five separate sequences are provided, each designed to measure specific characteristics. Marking, Microphones, Audio systems, Ratings, Designations, Instructions for use, Headphones, 6268 systems, Frequency response, Earphones, Audio equipment, Voltage measurement, Impedance measurement, Testing conditions, Preamplifiers, Comparative tests, Acoustic measurement, Electrical wave measurement, Electrical properties and phenomena, Acoustic testing.